Fuel Delivery
P0691
Fan 1 Control Circuit Low
P0691 — Fan 1 Control Circuit Low — is a Hero-tier Atlas chapter covering Fan 1 Control Circuit Low in the Cooling Fan Control system. The monitored result is circuit voltage below the calibrated electrical expectation.\n\nThe PCM evaluates cooling-fan command circuit and…
Diagnostic Snapshot
Atlas Academy
Learn the System
Before diagnosing this code, it helps to understand the system behind it.
Read Understanding Fuel Delivery SystemsTechnical Summary
P0691 — Fan 1 Control Circuit Low — is a Hero-tier chapter covering Fan 1 Control Circuit Low in Cooling Fan Control. The exact monitored result is circuit voltage below the calibrated electrical expectation.
The PCM evaluates cooling-fan command circuit and expected fan/module electrical or speed response. Freeze-frame and companion codes matter because voltage, temperature, load, crank/run state, and related inputs determine when many of these monitors run.
Start with proof: Command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation. Compare the commanded state with circuit behavior, physical response, and feedback.
Do not invent universal voltage, resistance, duty-cycle, pressure, or timing values. OEM circuit design and service specifications take priority.
Driveability: Drive only if operation is stable and no safety-related symptom is present. Diagnose promptly because electrical control faults can become intermittent no-start or limp-mode conditions.
What You'll Learn
- Exact meaning of P0691
- Monitor/enabling-condition logic
- Freeze-frame/live-data clues
- Command-versus-response testing
- Repair/programming verification
Think Like a Technician
Treat P0691 as evidence, not a parts order. The PCM evaluates cooling-fan command circuit and expected fan/module electrical or speed response.
Prove the chain: command/input → circuit → physical action → feedback. For module codes, prove external power, ground, network, and calibration first.
What This Code Means
P0691 — Fan 1 Control Circuit Low — is a Hero-tier Atlas chapter covering Fan 1 Control Circuit Low in the Cooling Fan Control system. The monitored result is circuit voltage below the calibrated electrical expectation.
The PCM evaluates cooling-fan command circuit and expected fan/module electrical or speed response. Exact thresholds and enabling criteria vary by calibration; OEM service information takes priority.
Start with proof: Command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation. Compare command/input, circuit behavior, physical response, and feedback before buying parts.
System Overview
Cooling Fan Control diagnosis separates PCM command/input, circuit integrity, physical response, and feedback. Expensive modules should be the last conclusion after external causes are proven good.
Why This Code Sets
The P0691 monitor runs when prerequisite power, sensor, and operating conditions are valid.
It evaluates cooling-fan command circuit and expected fan/module electrical or speed response.
The code stores when the monitored electrical or functional result remains outside the calibrated expectation. Internal-module codes require external voltage, ground, network, and programming causes to be eliminated before module condemnation.
Common Symptoms
- Check Engine Light
- Possible emissions-test failure
- Cooling fan may not run or may run continuously
- Possible overheating
- A/C performance may be affected
Most Likely Causes
- 1. fan motor/module fault
- 2. fuse/relay/feed problem
- 3. control wire fault
- 4. connector heat damage
- 5. incorrect temperature/A-C pressure input
- 6. PCM driver fault
Common Vehicles
Generic OBD-II code used across many makes. Exact circuit design, component naming, module ownership, calibration, fail-safe strategy, and thresholds vary by VIN.
Freeze Frame Clues
- System/cranking voltage
- RPM/load/vehicle speed
- ECT/IAT
- Commanded versus actual actuator state
- Related sensor/reference/network PIDs
- Companion module codes
- Key-on/crank/hot-soak/load context
Live Data Expectations
Graph fan command, coolant temperature, A/C pressure/request, and fan speed feedback if equipped. Commanded-on with no speed requires electrical/actuator testing; unexpected command may be input-driven.
Typical Verification Tests
- Confirm P0691 absent from current/pending memory
- Recreate freeze-frame condition
- Graph command and feedback
- Perform loaded circuit/waveform/current test
- Verify physical actuator/system response
- Verify programming/configuration where relevant
- Complete relearn/readiness
- Confirm original complaint resolved
Before You Condemn
- Confirm VIN-specific definition
- Save full scan/freeze-frame
- Verify battery/charging voltage
- Load-test powers/grounds
- Inspect connectors/terminals
- Compare command with physical response
- Verify network/programming
- Document failed test
Before Replacing Parts
Save freeze-frame/full scan. Command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation. Prove power, ground, circuit behavior, physical response, and required programming before replacement.
Diagnostic Workflow
- Confirm P0691; save current, pending, history, freeze-frame, and companion DTCs before clearing memory.
- Perform a complete module scan and note voltage, network, sensor-reference, or communication faults that could be foundational.
- Verify the VIN-specific code definition, wiring diagram, component identity, module ownership, enabling criteria, and service precautions.
- Test battery condition, charging voltage, module powers, and grounds under load before diagnosing electronic control faults.
- Inspect Fan 1 Control Circuit Low connectors/harnesses and related fuses, relays, grounds, plumbing, or mechanical hardware for visible damage.
- Command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation.
- Review live data: Graph fan command, coolant temperature, A/C pressure/request, and fan speed feedback if equipped. Commanded-on with no speed requires electrical/actuator testing; unexpected command may be input-driven.
- Reproduce the freeze-frame condition safely and note whether the fault is key-cycle, crank, idle, load, heat, vibration, or voltage dependent.
- Test the affected circuit while operating using loaded voltage-drop, current, or waveform methods appropriate to the design.
- Compare PCM command/input with an independent physical measurement or related feedback PID to separate an electrical reporting fault from a real system fault.
- Check shared references, power feeds, grounds, network paths, and companion actuators/sensors before replacing the named component.
- Wiggle-test and heat/cool suspect connectors, harnesses, relays, and modules while recording the relevant data if intermittent.
- For internal-module or programming codes, verify correct calibration, battery-support history, connector integrity, and network health before module replacement.
- Repair only the component, circuit, mechanical condition, programming, or module fault that failed a documented test.
- Perform required relearn, initialization, programming, or functional test after repair.
- Recreate the original condition and verify P0691 is absent from current and pending memory and the original complaint is resolved.
Labor & Inspection Checklist
- Verify VIN/service information
- Full scan/freeze-frame
- Power/ground inspection
- Connector/harness inspection
- Loaded circuit/waveform test
- Physical system verification
- Repair/relearn/program
- Monitor verification
Common Repairs
- Repair proven wiring/connector/power/ground fault
- Replace proven failed actuator/sensor/relay/module
- Correct verified mechanical or system fault
- Correct programming/configuration and perform required relearn
- Verify monitor completion
Common Parts
- Connector pigtail
- Harness/terminal repair materials
- Relay/fuse where proven
- Actuator/sensor/module only after diagnosis
Shop Notes
Monitor logic for P0691: identify the conditions that enabled the monitor. Voltage, temperature, crank/run state, load, and prerequisite sensor validity can change the meaning of the code.
Electrical proof for P0691: test the circuit loaded and operating. Continuity alone can miss high resistance, terminal fretting, relay contact loss, or a driver that fails only under current.
Command-versus-response for P0691: compare what the PCM requests with electrical feedback and the physical result. The first link that stops matching expectation is the diagnostic target.
Intermittent strategy for P0691: record the relevant PIDs/waveforms during controlled heat, vibration, key-cycle, and load testing. Preserve traces for post-repair comparison.
Module caution for P0691: never condemn a PCM solely from the DTC name. Verify powers, grounds, shared references, network integrity, calibration, and aftermarket modifications first.
Verification for P0691: reproduce the original condition, confirm normal command/feedback, complete required relearn/programming, and inspect pending memory.
Technician Notes
Diagnose the exact wording: circuit voltage below the calibrated electrical expectation.\n\nMonitor: cooling-fan command circuit and expected fan/module electrical or speed response.\n\nFirst move: command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation.\n\nPreserve full-scan and freeze-frame evidence.
Mechanic's Tip
For P0691, follow command → circuit → physical action → feedback. The first broken link is usually the fastest path to the root cause.
Common Mistakes
- Replacing the named module/actuator from the code alone
- Clearing freeze-frame too early
- Ignoring battery voltage and grounds
- Using continuity without loaded testing
- Ignoring shared references/network faults
- Skipping programming/configuration checks
- Skipping post-repair relearn/verification
Tools Used During Diagnosis
- Enhanced bidirectional graphing scan tool
- Digital multimeter
- OEM wiring diagram/service information
- Backprobe/terminal test tools
- Battery/charging-system tester
Manufacturer Notes
Generic OBD-II definition. Module ownership, circuit architecture, fail-safe behavior, reference sharing, programming requirements, and monitor thresholds vary by manufacturer and VIN. Use OEM service information before applying specifications.
Customer Explanation
Your vehicle stored P0691, meaning the computer found circuit voltage below the calibrated electrical expectation in the Cooling Fan Control system. The code does not automatically prove the named component is bad; wiring, power, programming, or the controlled system can cause it.
Frequently Asked Questions
What does P0691 mean?
P0691 means the PCM identified circuit voltage below the calibrated electrical expectation involving Fan 1 Control Circuit Low. It describes a failed monitor, not automatically a failed part.
Can I drive with P0691?
Drive only if operation is stable and no safety-related symptom is present. Diagnose promptly because electrical control faults can become intermittent no-start or limp-mode conditions.
What should I check first for P0691?
Command the fan bidirectionally and verify fuse/feed/ground, control output, and actual fan operation. Save freeze-frame first.
Does P0691 prove the module or actuator is bad?
No. Power, grounds, wiring, shared references, mechanical conditions, programming, and network faults can create the same code.
Can low battery voltage cause P0691?
Yes. Voltage instability can create false control, reference, communication, and internal-module faults.
Will P0691 affect emissions testing?
Usually yes when the MIL is commanded on; clearing codes can also reset readiness monitors.
Should I clear P0691 before diagnosis?
No. Freeze-frame, pending status, companion codes, and module reset history are useful evidence.
When is professional equipment justified?
When basic inspection does not prove the fault. Bidirectional scan data, an oscilloscope/current clamp, network tools, pressure testing, or OEM programming may be required.
Can P0691 be intermittent?
Yes. Heat, vibration, terminal fretting, relay contacts, voltage changes, and module resets can make the fault disappear in the bay.
How do I verify the repair?
Repeat the original operating condition, confirm command and feedback agree, complete required initialization/programming, and verify no current or pending code returns.
Related Atlas Resources
Use the related Atlas system chapter plus VIN-specific OEM service information for specification-level testing.
Diagnostic Confidence
High after the fault is reproduced and the circuit/physical cause is proven; Medium when intermittent and not reproducible
Related Codes
Project Atlas Feedback
Was this article helpful?
Needs Improvement
Working on this repair?
Create a professional estimate in minutes.
Why Trust This Guide?
Built by mechanics. Improved by mechanics.
This guide is maintained for working mechanics, mobile technicians, fleet maintenance professionals, and independent repair shops.