Powertrain Codes

Good

P0967

Pressure Control Solenoid B Control Circuit High

★★★ Common diagnostic code

P0967 means the vehicle detected a fault related to pressure control solenoid b control circuit high. On most vehicles this points to the transmission, driveline, clutch, or control circuit that needs testing before parts are replaced.

Atlas Quality75% · Good
Editorial StatusGood
SeverityHigh
Can I keep driving?Use caution and diagnose before replacing parts.
Typical repair cost$150-$2,500+
Typical labor0.8-5.0 hours

What P0967 Means

P0967 means the vehicle detected a fault related to pressure control solenoid b control circuit high. On most vehicles this points to the transmission, driveline, clutch, or control circuit that needs testing before parts are replaced.

Before You Replace Anything

Record the evidence first. Clearing codes too early can erase the clues that point to the real fault.

✓ Save freeze-frame data✓ Check for additional trouble codes✓ Look for technical service bulletins✓ Verify battery voltage✓ Verify engine oil level and coolant level✓ Perform a visual inspection✓ Do not clear the codes yet

Common Symptoms

⚠ Check Engine Light⚠ Transmission warning light⚠ Harsh shifting⚠ Slipping⚠ Delayed engagement⚠ Limp mode

Most Common Causes

Low or contaminated transmission fluid90%
Faulty pressure sensor or switch78%
Faulty pressure control solenoid66%
Valve body issue54%
Wiring or connector fault42%
Internal transmission wear30%

Diagnostic Confidence

Transmission fluid88%
Pressure sensor78%
Pressure switch68%
Pressure control solenoid58%
Valve body48%

Use this as a starting point, not a replacement for testing.

Recommended Diagnostic Workflow

1Check transmission fluid level and condition
2Scan transmission live data and freeze-frame data
3Inspect wiring and connectors at the transmission
4Compare commanded pressure to actual pressure if data is available
5Test sensor or solenoid circuits before replacing parts
6Road test while monitoring shift timing and pressure data

Mechanic's Tips

Tip #1

Save freeze-frame data and check for related transmission, communication, voltage, and module codes. Always verify fluid level/condition and electrical integrity before condemning a sensor, solenoid, actuator, or module.

Common Mistakes to Avoid

✕ Replacing parts before testing power, ground, and signal circuits✕ Ignoring related codes and freeze-frame data✕ Skipping the visual inspection✕ Clearing codes before confirming the repair

Common Repairs

Correct transmission fluid level or condition

Success Rate: ★★★☆☆

Average Cost: $150-$2,500+

Labor: 0.8-5.0 hours

Repair wiring or connector damage

Success Rate: ★★★☆☆

Average Cost: $150-$2,500+

Labor: 0.8-5.0 hours

Replace confirmed failed pressure sensor or switch

Success Rate: ★★★☆☆

Average Cost: $150-$2,500+

Labor: 0.8-5.0 hours

Replace failed pressure control solenoid

Success Rate: ★★★☆☆

Average Cost: $150-$2,500+

Labor: 0.8-5.0 hours

Parts Commonly Replaced

Transmission fluidPressure sensorPressure switchPressure control solenoidValve bodyTransmission harness

Tools Used During Diagnosis

OBD-II scan toolDigital multimeterBasic hand toolsManufacturer service information

Related Repairs

Diagnostic workflowComponent testingWiring inspectionRepair estimate checklist

How to Explain This to Your Customer

Your vehicle stored P0967, which points to a problem with pressure control solenoid b control circuit high. The next step is diagnosis of the related circuit or component so the repair is based on test results instead of guessing.

Manufacturer Notes

Generic OBD-II information. Exact test steps, component names, connector locations, relearn procedures, and repair strategy may vary by make, model, year, transmission, and calibration.

Technician Notes

Save freeze-frame data and check for related transmission, communication, voltage, and module codes. Always verify fluid level/condition and electrical integrity before condemning a sensor, solenoid, actuator, or module.

Related Codes

P0840 P0841 P0842 P0843 P0868 P0870 P0871 P0872

FAQ

What does P0967 mean?

P0967 means the computer detected a fault related to pressure control solenoid b control circuit high.

Is P0967 serious?

It can be. Transmission, clutch, or driveline faults can lead to limp mode, harsh shifting, no-start conditions, or additional damage if ignored.

Can I drive with P0967?

Avoid extended driving if the vehicle shifts poorly, slips, overheats, or enters limp mode. Diagnose it before continuing normal use.

Will P0967 fail emissions?

It may fail emissions if the Check Engine Light is on or readiness monitors are incomplete.

Project Atlas Feedback

Was this article helpful?

👎 Needs Improvement
Project Atlas Built by mechanics. Improved by mechanics.

Working on this repair?

Create a professional estimate in minutes.

✓ Email it to your customer✓ Track labor and parts✓ Convert it into an invoice✓ Keep a complete repair history
Start Free PistonCMS Account

Project Atlas

Chapter Status

Quality Score75%
Editorial StatusGood
Last ReviewedPending review
Template Version1.3.4

Editorial Readiness

Reference Chapter Checklist

○ Academy linked○ Quality Score ≥95✓ FAQ complete✓ Customer explanation✓ Internal links○ Reviewed

Why Trust This Guide?

✓ Updated regularly✓ Written for working technicians✓ Practical diagnostic process✓ Built for mobile mechanics and independent shops✓ Maintained by PistonCMS

Built by mechanics. Improved by mechanics.

This guide is maintained for working mechanics, mobile technicians, fleet maintenance professionals, and independent repair shops.