Powertrain Codes

Good

P1067

Secondary Air Injection Flow Performance

★★★★ Common diagnostic code

P1067 means the vehicle detected a fault related to secondary air injection flow performance. The code points to the system that needs testing, but the exact repair should be confirmed with scan data, visual inspection, and circuit or mechanical checks.

Atlas Quality75% · Good
Editorial StatusGood
SeverityMedium
Can I keep driving?Use caution and diagnose before replacing parts.
Typical repair cost$75-$900
Typical labor0.5-2.5 hours

What P1067 Means

P1067 means the vehicle detected a fault related to secondary air injection flow performance. The code points to the system that needs testing, but the exact repair should be confirmed with scan data, visual inspection, and circuit or mechanical checks.

Before You Replace Anything

Record the evidence first. Clearing codes too early can erase the clues that point to the real fault.

✓ Save freeze-frame data✓ Check for additional trouble codes✓ Look for technical service bulletins✓ Verify battery voltage✓ Verify engine oil level and coolant level✓ Perform a visual inspection✓ Do not clear the codes yet

Common Symptoms

⚠ Check Engine Light⚠ Failed emissions test⚠ Possible fuel odor⚠ Poor fuel economy⚠ Usually mild drivability symptoms

Most Common Causes

Faulty emissions sensor or valve90%
Vacuum leak78%
Exhaust leak66%
EVAP leak54%
Damaged wiring or connector42%
Carbon buildup30%

Diagnostic Confidence

EVAP valve88%
Vacuum hose78%
Oxygen sensor68%
EGR valve58%
Exhaust gasket48%

Use this as a starting point, not a replacement for testing.

Recommended Diagnostic Workflow

1Record freeze-frame data
2Check for related fuel trim or emissions codes
3Inspect hoses, valves, wiring, and connectors
4Review live sensor data
5Smoke test EVAP or intake system if applicable
6Complete drive cycle after repair

Mechanic's Tips

Tip #1

Save freeze-frame data before clearing codes. Check related codes, voltage, grounds, wiring integrity, connector condition, and manufacturer service information before replacing parts.

Common Mistakes to Avoid

✕ Replacing parts before testing power, ground, and signal circuits✕ Ignoring related codes and freeze-frame data✕ Skipping the visual inspection✕ Clearing codes before confirming the repair

Common Repairs

Repair vacuum or EVAP leak

Success Rate: ★★★☆☆

Average Cost: $75-$900

Labor: 0.5-2.5 hours

Replace confirmed failed sensor or valve

Success Rate: ★★★☆☆

Average Cost: $75-$900

Labor: 0.5-2.5 hours

Repair wiring or connector

Success Rate: ★★★☆☆

Average Cost: $75-$900

Labor: 0.5-2.5 hours

Clean carbon buildup where applicable

Success Rate: ★★★☆☆

Average Cost: $75-$900

Labor: 0.5-2.5 hours

Parts Commonly Replaced

EVAP valveVacuum hoseOxygen sensorEGR valveExhaust gasketConnector pigtail

Tools Used During Diagnosis

OBD-II scan toolDigital multimeterBasic hand toolsManufacturer service information

Related Repairs

Diagnostic workflowComponent testingWiring inspectionRepair estimate checklist

How to Explain This to Your Customer

Your vehicle stored code P1067, which points to a problem with secondary air injection flow performance. The next step is proper diagnosis so parts are not replaced blindly.

Manufacturer Notes

Generic OBD-II information. Exact test steps, component locations, relearn procedures, and known failures may vary by make, model, year, engine, transmission, and calibration.

Technician Notes

Save freeze-frame data before clearing codes. Check related codes, voltage, grounds, wiring integrity, connector condition, and manufacturer service information before replacing parts.

Related Codes

P0171 P0174 P0401 P0420 P0440 P0442 P0455 P0456

FAQ

What does P1067 mean?

P1067 means the computer detected a fault related to secondary air injection flow performance.

Is P1067 serious?

It depends on symptoms. Warning lights, overheating, slipping, rough running, limp mode, or poor drivability should be diagnosed quickly.

Can I drive with P1067?

Short trips may be possible if the vehicle runs normally, but avoid driving if the light is flashing, the vehicle overheats, shifts poorly, or loses power.

Will P1067 fail emissions?

Usually yes if the Check Engine Light is on or readiness monitors are incomplete.

Project Atlas Feedback

Was this article helpful?

👎 Needs Improvement
Project Atlas Built by mechanics. Improved by mechanics.

Working on this repair?

Create a professional estimate in minutes.

✓ Email it to your customer✓ Track labor and parts✓ Convert it into an invoice✓ Keep a complete repair history
Start Free PistonCMS Account

Project Atlas

Chapter Status

Quality Score75%
Editorial StatusGood
Last ReviewedPending review
Template Version1.3.4

Editorial Readiness

Reference Chapter Checklist

○ Academy linked○ Quality Score ≥95✓ FAQ complete✓ Customer explanation✓ Internal links○ Reviewed

Why Trust This Guide?

✓ Updated regularly✓ Written for working technicians✓ Practical diagnostic process✓ Built for mobile mechanics and independent shops✓ Maintained by PistonCMS

Built by mechanics. Improved by mechanics.

This guide is maintained for working mechanics, mobile technicians, fleet maintenance professionals, and independent repair shops.