Fuel Delivery
P1113
Intake Air Temperature Sensor Open Circuit
P1113 — Intake Air Temperature Sensor Open Circuit — is a Hero-tier Atlas chapter for Air Intake and Throttle Control.\n\nThe monitor evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response. The fault is electrical circuit behavior outside the…
Diagnostic Snapshot
Atlas Academy
Learn the System
Before diagnosing this code, it helps to understand the system behind it.
Read Understanding Fuel Delivery SystemsTechnical Summary
P1113 — Intake Air Temperature Sensor Open Circuit — covers Air Intake and Throttle Control; confirm the VIN-specific P1xxx definition first.
The monitor evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response. The fault is electrical circuit behavior outside the manufacturer-defined valid range.
First test: inspect for air leaks or binding and graph commanded/actual position with MAP, MAF, load, and fuel trims. OEM specifications and enabling criteria take priority.
What You'll Learn
- VIN-specific meaning of P1113
- Monitor/enabling logic
- Freeze-frame clues
- Live-data patterns
- Electrical versus physical-system testing
- Before-you-condemn checks
- Repair verification
Think Like a Technician
Treat P1113 as a failed monitor, not a failed-part label. The controller evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response.
Prove prerequisites first, then electrical signal/command, then physical response. This prevents replacing a sensor for a real system fault or expensive hardware because of biased data.
What This Code Means
P1113 identifies electrical circuit behavior outside the manufacturer-defined valid range involving Intake Air Temperature Sensor Open Circuit.
The controller evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response. Because this is P1xxx, verify the scan-tool definition against the exact VIN.
The DTC identifies a failed monitor relationship, not automatic proof of a failed named component.
System Overview
Air Intake and Throttle Control diagnosis compares command/input, circuit feedback, and physical response so electrical faults are separated from real system-performance failures.
Why This Code Sets
The P1113 monitor runs only when manufacturer-defined voltage, temperature, engine-state, sensor-plausibility, and system prerequisites are valid.
It evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response.
The DTC stores when circuit, signal, command feedback, or physical response remains outside the calibrated expectation for the required samples or duration. Exact thresholds are calibration-specific.
Common Symptoms
- Check Engine Light
- Reduced power possible
- Hard starting/stalling possible depending on system
- Fuel economy/performance change possible
- Emissions failure possible
- System-specific warning possible
Most Likely Causes
- 1. air/throttle/manifold actuator or position-sensor fault
- 2. intake leak or restricted airflow
- 3. carbon/oil deposits causing binding
- 4. power/ground/reference/signal circuit fault
- 5. biased MAP/MAF or related load input
- 6. PCM driver/input fault after external proof
Common Vehicles
Manufacturer-specific P1xxx code. The same numeric code can have different definitions or component assignments across makes and powertrains. Confirm the VIN-specific definition.
Freeze Frame Clues
- Engine RPM
- Calculated load
- Vehicle speed
- Battery voltage
- Coolant/engine temperature
- Relevant command/feedback PID
- Related pressure/flow/timing/mixture/exhaust data
- Companion DTCs
Live Data Expectations
Graph commanded/actual actuator position with MAP, MAF, RPM, throttle/pedal input, load, and fuel trims. Determine whether position feedback is wrong or airflow response is physically implausible.
Typical Verification Tests
- Confirm P1113 absent from current/pending memory
- Repeat original freeze-frame condition
- Graph command/input and feedback together
- Perform loaded circuit test
- Use independent physical measurement where applicable
- Confirm prerequisite codes remain absent
- Complete required relearn/service procedure
- Verify normal driveability/readiness
Before You Condemn
- Confirm VIN-specific P1xxx definition
- Save full scan/freeze-frame
- Verify battery/module powers and grounds
- Inspect connector/harness and recent repairs
- Graph related PIDs
- Perform loaded circuit testing
- Verify physical pressure/flow/movement/temperature where applicable
- Check service bulletins/calibration before module replacement
Before Replacing Parts
Confirm the VIN-specific definition and save freeze-frame. Inspect for air leaks or binding and graph commanded/actual position with map, maf, load, and fuel trims. Prove circuit integrity and physical response before replacement.
Diagnostic Workflow
- Confirm P1113; save current, pending, history, freeze-frame, readiness status, and companion powertrain/network DTCs.
- Confirm the VIN-specific definition of Intake Air Temperature Sensor Open Circuit; P1xxx definitions, component assignments, bank designations, and thresholds are manufacturer controlled.
- Review OEM wiring, component location, enabling criteria, service bulletins, calibration notes, and monitor strategy for Air Intake and Throttle Control.
- Verify battery/charging voltage and module powers/grounds under load before interpreting electronic behavior.
- Inspect the Air Intake and Throttle Control system for connector damage, terminal fit, harness routing, leaks, restrictions, contamination, fluid condition, heat damage, and recent repair disturbance.
- Inspect for air leaks or binding and graph commanded/actual position with map, maf, load, and fuel trims.
- Review live data: Graph commanded/actual actuator position with MAP, MAF, RPM, throttle/pedal input, load, and fuel trims. Determine whether position feedback is wrong or airflow response is physically implausible.
- Reproduce the freeze-frame operating condition safely when practical, including temperature, load, speed, command state, and enable prerequisites.
- Test the affected circuit dynamically with loaded voltage-drop, current, frequency, or waveform methods appropriate to the design; use OEM specifications for exact values.
- Use bidirectional control when supported to command the affected pump, valve, actuator, heater, throttle, timing, or emissions function while watching feedback and physical response.
- Compare scan feedback with an independent measurement such as mechanical pressure, vacuum/boost, temperature, actuator movement, exhaust response, smoke test, or oscilloscope signal when applicable.
- Test prerequisite sensors used by the monitor for plausibility; biased pressure, temperature, airflow, position, or emissions data can misdirect diagnosis.
- Check restrictions, leaks, contamination, fluid-quality problems, carbon, hydraulic losses, exhaust leaks, or mechanical wear that can prevent the expected response.
- Before condemning a control module, prove powers, grounds, network integrity where used, circuit load capability, terminal tension, component current draw, and software/calibration status.
- Repair only the wiring, sensor, actuator, valve, pump, fluid, mechanical, emissions, calibration, or module fault that failed a documented test.
- Complete required relearns/service procedures, repeat the original enable condition, and verify P1113 does not return current or pending.
Labor & Inspection Checklist
- VIN/engine/system identification
- Full scan/freeze-frame
- Visual/fluid/leak/restriction inspection
- Connector/power/ground inspection
- Live-data correlation
- Dynamic electrical test
- Independent physical test where applicable
- Repair/relearn/road-test/readiness verification
Common Repairs
- Repair proven connector/harness/power/ground fault
- Replace proven sensor/valve/actuator only after testing
- Correct verified fluid/pressure/leak/restriction/contamination issue
- Repair mechanical/emissions cause only after independent evidence
- Complete required relearn/programming and verification
Common Parts
- Connector/terminal repair materials
- System-specific sensor/actuator where proven
- Hoses/lines/seals where proven
- Control valve/pump/heater where proven
- Mechanical/emissions parts only after diagnosis
Shop Notes
Monitor logic for P1113: reproduce the engine state, temperature, load, and enable conditions shown in freeze-frame before deciding a stationary test disproves the fault.
Electrical proof for P1113: static continuity is not enough. Check terminal fit and circuit behavior under load.
Plausibility strategy for P1113: compare related PIDs rather than trusting one value. The controller evaluates air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response.
Physical-response strategy for P1113: if command and circuit feedback are correct, verify actual pressure, flow, temperature, timing movement, airflow, mixture, or exhaust response.
Intermittent strategy for P1113: graph relevant PIDs while temperature, vibration, harness position, and load change.
Before expensive hardware for P1113: prove powers, grounds, terminal tension, circuit load capability, prerequisite sensors, and software/calibration status.
Verification for P1113: repeat the original event, confirm the monitored relationship is normal, check pending memory, and confirm required readiness/self-tests can complete.
Technician Notes
Exact fault: electrical circuit behavior outside the manufacturer-defined valid range.\n\nMonitor focus: air/throttle/manifold command and position versus MAP, MAF, RPM, load, and fuel-trim response.\n\nFirst move: inspect for air leaks or binding and graph commanded/actual position with MAP, MAF, load, and fuel trims.\n\nPreserve freeze-frame and companion codes before clearing memory.
Mechanic's Tip
For P1113, follow prerequisites → controller command/input → circuit feedback → physical response → confirmation data. The first point that stops agreeing determines the next test.
Common Mistakes
- Assuming a P1xxx definition is universal
- Replacing the named component from the code alone
- Ignoring companion prerequisite codes
- Using universal specifications
- Skipping loaded circuit testing
- Ignoring restrictions/leaks/fluid/mechanical faults
- Clearing freeze-frame before recording it
Tools Used During Diagnosis
- Manufacturer-enhanced graphing scan tool
- Digital multimeter
- Oscilloscope/current clamp where appropriate
- VIN-specific OEM service information
- Backprobe/terminal tools
- Mechanical pressure/smoke/temperature equipment as applicable
- Bidirectional controls where supported
Manufacturer Notes
P1xxx codes are manufacturer-controlled. Confirm the exact VIN-specific definition, component/bank assignment, circuit design, enabling criteria, thresholds, service procedures, and software information.
Customer Explanation
P1113 means the computer found a problem involving Intake Air Temperature Sensor Open Circuit. Testing is required before replacing the part named by the code.
Frequently Asked Questions
What does P1113 mean?
P1113 indicates electrical circuit behavior outside the manufacturer-defined valid range involving Intake Air Temperature Sensor Open Circuit. Confirm the VIN-specific manufacturer definition before testing.
Can I drive with P1113?
Driveability depends on the failure mode. Limit driving for stalling, overheating, severe power loss, misfire, erratic throttle response, or reduced-power operation.
What should I check first for P1113?
Inspect for air leaks or binding and graph commanded/actual position with map, maf, load, and fuel trims.
Does P1113 prove the named part is bad?
No. Wiring, power/ground, prerequisite inputs, restrictions, leaks, fluid condition, and mechanical response must be tested before replacement.
Can low battery voltage contribute to P1113?
Yes. Unstable voltage can alter sensor references, actuator current, pump/heater operation, network communication, and learned control behavior.
Will P1113 affect emissions testing?
It can. A commanded MIL can fail inspection, and fuel, airflow, timing, oxygen-sensor, or emissions-control faults can prevent readiness monitors from completing.
Can P1113 be intermittent?
Yes. Heat, vibration, terminal tension, moisture, contamination, wiring movement, fluid temperature, and mechanical sticking can create intermittent faults.
When is professional equipment justified?
Professional equipment is justified for manufacturer-enhanced data, bidirectional controls, waveform/current testing, smoke testing, mechanical pressure measurement, emissions service functions, or programming.
Could another DTC be the root cause?
Yes. Shared voltage, pressure, temperature, airflow, oil-system, exhaust, mixture, or network faults can cause this monitor to fail. Diagnose primary shared faults first.
How do I verify the repair?
Repeat the original freeze-frame condition, confirm command/input and physical response agree, complete required relearns, and verify no current or pending DTC returns.
Related Atlas Resources
Use VIN-specific OEM definitions, specifications, tests, and relearns.
Diagnostic Confidence
High after the VIN-specific definition is confirmed and the failed electrical or physical response is reproduced; Medium when intermittent or documentation is incomplete
Related Codes
Project Atlas Feedback
Was this article helpful?
Needs Improvement
Working on this repair?
Create a professional estimate in minutes.
Why Trust This Guide?
Built by mechanics. Improved by mechanics.
This guide is maintained for working mechanics, mobile technicians, fleet maintenance professionals, and independent repair shops.